How to Repair The Spine of a Child's Board Book


Children’s books often need repairs!

I have a foam puzzle book that I purchased for my grandchildren many years ago. This fun board book has proven to be a constant favorite for toddlers who visit my home. Unfortuantely, one of my grands loved it so much that the spine broke and need some TLC.

At first, this repair appeared to be a difficult one to make, but it proved to be quite easy because I used the correct glue for the project. The most important qualities the glue needed were strength and flexibility when dried. The book repair glue I finally decided to use was Tacky Glue. It is not pH neutral, but that is ok for this repair project. At least I did not have to use tape to hold this book together.

Below you will find step-by-step photos detailing the spine repair I made to this much loved children’s book. The technique can also be used to repair a spine on a paper book, as well.

By the way, teachers might find this page helpful for their in class library.

NOTE: for antique or valuable books, please consult a true professional who is an expert. I am neither! I am just a former librarian who learned some nice tricks to repair books that get used every day.

All images were taken by me using my iPhone. The quality is not professional, but I do not want anyone to use them without permission and attribution.

The Supplies I used to fix this book: – Easily found and ordered from Amazon!

For this specific repair, I used Aleene’s Original Tacky glue even though it is not pH neutral. I do not expect the foam book to be around forever and ever. It is not valuable, but my grandchildren love it and constantly get it off the shelf to look at and play with. The child who accidentally broke it was heartbroken. Now, she will be very happy that I repaired it.

You will find Amazon links below to order what you will need. Thank you in advance for purchasing your supplies from this page.

Disclosure: Mickie_G is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.

I need to reattach the purple foam square cover (on the left in the image above) to the rest of the book by gluing the spine side of the page to the next page.

You can see the spine cover between the two halves of the book. It is still attached to the book and the front cover piece.

I did not want to use tape to fix the book because I would need a tape that was at least 2 inches wide. Packing tape would have been the obvious choice if I wanted to go that route. I did not want to do that because if even a little bit of the tape became loose, a child would pick at it. You know that i am right! If I had used cloth tape, the images would have been covered up and spoiled the look of this colorful book.

Each page of the foam book is about 1/4 inch thick. Only the top purple “page” or the cover needed to be reattached to the rest of the book.

Protect your work surface!

No, I did not put glue on the tablecloth! I used a piece of plastic laminate under the book and squeezed out a quarter sized glob of glue on it. I chose Tacky Glue because it is very thick and strong. I also had it on hand. Elmer’s School Glue would have been too thin, in my opinion. You can used waxed paper under the book or a paper plate, too, and squirt the glue on it. As it turned out, I had squeezed out more than enough glue. A dime sized glob would have been enough.

Using a toothpick, I applied the glue just to the torn edges all down the length of the spine. Use enough, but do not go over-board. A little bit goes a long way. Apply the glue to both pages.

You can use a thin brush to apply the glue if you have one; just be sure to wash the glue out of the bristles using warm water and mild soap.

After I applied the glue to both edges of pages of the book, I carefully put the two pieces together along the edges where the paper was torn. I held the book open, gently pushing the pages together and held it in place for about 5 minutes. I do this because the book is designed to be opened; I did not want the pages glued together in a closed position at the beginning of the repair. I then used a piece of waxed paper and put it right up even with the fold in the book.

Do you understand? See the image that follows to get a visual.

Photo is just a detail of me holding the book open while the glue sets. This step makes sure that the book will open with no stress to the spine after the repair is completed.

Using waxed paper along the spine before you close it, keeps the glue from finding its way onto the page where you do not want it. You do not want to glue the pages together, just where the spine fold is located. Put the paper right up in the fold and hold it there when you close the book. Reposition it if necessary.

I used the bottle of glue as my “weight” since the foam book was not heavy. You can use another book, too, just as long as it is a little heavier. Just make sure that the book getting repaired is not disturbed while it is drying. To be safe, let the book dry for about an hour before removing the weight.

If you look closely at the spine of the book in the lower left, you can see that the spine cover is torn.

I used the toothpick to apply a small amount of glue and then gently pressed the torn edges together.

Patience! Hold you finger there for about a minute until the glue sets just a little.

You do not have to be a member of Squidoo to leave a comment. Please feel free to ask any questions, too. I will be very happy to respond. After all, it is my goal in life to “save the world, one book at a time”!

Leave a Reply

Your email address will not be published. Required fields are marked *

error

Enjoy this blog? Please spread the word :)

Follow by Email
LinkedIn
Share
Instagram